Exactly How to Install a Bath Tub
Exactly How to Install a Bath Tub
Blog Article
They are making a number of good pointers on A Step-by-Step Guide to Installing a Bathtub in general in the content further down.
Mounting a bath tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, as well as occasionally, tiling abilities. Changing an old tub with a brand-new one is likewise a moderately challenging project. If the old tub is readily accessible, the task can relocate easily; if you need to open a wall to remove the old tub and place the brand-new tub, the job is much harder. In either case, the project is within a home handyman's abilities, although you will certainly need a helper to move out the old bathtub and also embeded in the new one. Ensure you have actually qualified yourself for the job and also are comfortable attempting it. As opposed to employing a contractor to take control of a halfway-completed job, it is better to take into consideration utilizing one before you start. Possibilities are you may need a specialist plumber to make tube connections.
This write-up will aid you set up a new bath tub in your restroom if you have actually already bought a brand-new tub and also don't require to alter the setup of your previous water system pipes.
Your devices and product checklist must comprise the following:
Planning for the Installation
To start with, the sustaining frame provided with the bath needs to be fitted (if needed) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to see to it that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to stop strain on the bath tub.
Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be fitted in its last placement.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be fairly bothersome due to the restricted gain access to that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a cloth prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipes have been removed, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming during this process. Once the taps have been removed, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Before carrying on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Installing the Bathtub
Using both wood boards under its feet, position the bath tub in the needed setting. The wooden boards are helpful in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The next objective is to make sure that the tub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bath tub till the spirit level reads degree.
To set up taps, fit all-time low of the outermost versatile tap adapter to the suitable supply pipe by making a compression sign up with; then do the same for the various other faucet.
Switch on the water as well as check all joints and also brand-new pipework for leaks as well as tighten them if necessary. Load the bath tub and also examine the overflow electrical outlet as well as the normal electrical outlet for leakages.
Lastly, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the bathtub needs to wait up until the bathtub has actually been utilized at least once as this will resolve it into its final placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the installing opening in the bath/basin guaranteeing that the washing machines remain in place in between the faucet and the sink. Safeguard the tap in place with the supplier offered backnut. When the faucet is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap adapters. The former type needs to be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath satisfies the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to split an inflexible seal, causing the water to permeate the wall surface in between the bathroom and the tiling, resulting in issues with wetness and possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your components and fittings. They are offered in tubes as well as cartridges, and also can securing gaps up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Remember to always fill the bathtub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can fracture rather very early if you do not take into account this activity prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the market. It is advisable to fit the tiles using waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our excerpt on Tools You Need to Install a New Bathtub . Thanks a lot for spending some time to read through our blog post. Enjoyed reading our content? Please share it. Help somebody else discover it. Thank-you for going through it.
Get A Quote Report this page